To customize your network settings, manage security, or view connected devices, you must log into the web-based gateway interface. Logging In
By default, the Sagemcom C2 uses "Smart Wi-Fi" (band steering) to merge the 2.4GHz and 5GHz bands under one name. This often forces fast devices onto the slower 2.4GHz band.
The (also identified as the F@st 3890 Com Hem ) is a high-speed cable gateway. Below are the key setup and management details typically found in its user manual. 0;92;0;a1; 0;baf;0;15b; Getting Started & Setup 0;f63;0;ace;
: Open a web browser on a connected device and enter the default IP address (often 192.168.1.1 or 192.168.40.1 , depending on your service provider) 0;a6e;.
: Use the SSID and WPA password found on the label at the bottom or back of the hub to connect via WiFi. For wired connections, use any of the four yellow Technical Specifications Max Speeds 4000 Mbps Down / 1200 Mbps Up WiFi Standards 802.11ac Wave 2 (Dual-band: 2.4GHz & 5GHz) Antenna Config 4x4 antennas for both 2.4GHz and 5GHz bands 4 x RJ45 GigE LAN ports, 1 x Coaxial, 2 x TEL ports Troubleshooting & Maintenance Master Reset sagemcom wifi hub c2 manual best
Open a web browser and enter the router's default IP address (found on the bottom label). Log in using the factory admin credentials printed on the label. Navigate to the configuration panel to update your WiFi name and password Technical Specifications Max Download Up to 4000 Mbit/s Max Upload Up to 1200 Mbit/s WiFi Standards 802.11a/b/g/n/ac Wave 2 with bandsteering 4 x LAN RJ45 (10/100/1000 Mbps), 1 x Coaxial Dimensions 234 x 190 x 69 mm Official Manuals & Resources
If you have full-fibre internet, connect an Ethernet cable from your Openreach/ISP fibre modem into the red port on the back of the hub.
The Sagemcom Hub has a simple light system to tell you exactly what is wrong:
Keeps one Wi-Fi name. The router chooses the best band for your device. To customize your network settings, manage security, or
It is highly recommended to change the default Wi-Fi password for security (see Section 4). 4. Accessing the Admin Panel (192.168.1.1)
The (often identified within the F@st 5366 series or as a provider-specific hub, such as the Com Hem C2) is a high-performance router designed to deliver stable, high-speed internet to modern homes. To get the "best" out of this device, you need to understand its key functions, optimal placement, and advanced settings. This article serves as the comprehensive manual for setup, troubleshooting, and optimization. Table of Contents Getting Started: Unboxing & Physical Setup Best Practices: Optimal Router Placement Connecting Devices & Configuring WiFi Accessing the Admin Panel (192.168.1.1) Advanced Settings for Best Performance Troubleshooting: Common Issues 1. Getting Started: Unboxing & Physical Setup
: You can find your default SSID (WiFi name) and WPA2 password on the label located on the underside or back of the gateway 18;write_to_target_document7;default0;16f;18;write_to_target_document1a;_gUXuafyYNbLG4-EPpqne6AY_20;a7a;.
Ultimate Guide to the Sagemcom WiFi Hub C2 : Manual & Optimization Tips The , commonly known as the WiFi Hub C2 The (also identified as the F@st 3890 Com
Document prepared from common ISP documentation – settings may vary slightly by provider.
The hub is actively looking for a broadband signal.
For connecting network-attached storage (NAS) or media drives.
4x4 MIMO on 5 GHz, 3x3 MIMO on 2.4 GHz Physical Ports: 1 x WAN Port (Link to your Openreach modem/ONT)
Place the hub in a central, open location. Keep it off the floor and away from electronic devices like microwaves, cordless phones, and baby monitors.